Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Burbank
Gate parts and welding in Burbank usually means one of three things: a twisted steel frame after a Santa Ana wind event, a worn-out slide gate on a studio lot cycling hundreds of times daily, or an original 1950s hinge that finally gave up. Whatever brought you to this page, we can fix it. Ironworks Gate Co. has welded, rebuilt, and remounted driveway and estate gates across 91501, 91502, and 91503 for years, and our crews are on site anywhere in Burbank the same day you call. The price is quoted and agreed before any work starts, and every job is covered by our written 90-Day Done Right Promise. If you’re looking at a gate that won’t close, a post leaning out of plumb, or a hinge that’s sheared clean off, call (925) 590-4289 now. A live person answers, 24 hours a day, every day.
Why Burbank Homeowners Call Ironworks Gate Co. for Gate Parts & Welding
Most gate companies in the Los Angeles area are generalists. They hang a door, patch a fence, maybe weld a bracket, and move on. We don’t work that way. Gate repair, welding, and parts work is all we do, and it’s been our entire focus for over 42 years. Led by Victor Salinas, our team of background-checked, uniformed technicians treats your Burbank property the way we’d treat our own mother’s house - clean work, straight answers, and a gate that operates right when we leave.
Burbank is a unique market for gate work. The combination of post-war ranch homes in 91501 and 91502, high-value estate properties, and the dense stretch of production facilities along Olive Avenue and Alameda Avenue means we see repair demands here that don’t exist ten minutes away in North Hollywood or Studio City. We know the difference between a 1950s steel tube gate that can be saved and one that needs a full frame rebuild. We know which Burbank neighborhoods get the worst wind-load damage during Santa Ana events. And we carry the parts, stock, and welding equipment needed to finish most jobs in a single visit.
When you call Gate Parts & Welding at Ironworks, you’re not routed through a call center. A live person picks up, every time, 24/7. You’ll get a straight answer about scheduling, and we’ll give you an upfront price before any work begins.
Our Gate Parts & Welding Services in Burbank
Here’s what we handle most often in Burbank, and how each job typically goes:
Hinge Replacement
On Burbank post-war ranch homes, the original hinges were sized for a lighter gate than what’s hanging today. Sixty years of Santa Ana gusts, sun exposure, and daily use work-harden the steel until a barrel cracks or a leaf shears. We replace your hinges with heavier-duty options matched to the gate’s actual weight and the wind load your property sees. For solid infill swing gates - the style that’s common in 91501 and 91502 - that often means stepping up to HD barrel hinges or weld-on adjustable hinges. A typical hinge replacement in Burbank runs $180-$340, including realignment and lubrication.
Post Replacement
A gate post that’s leaning, rotating in its footing, or cracked at the base is a structural failure, not a cosmetic one. Burbank’s clay-heavy soil absorbs winter storm water and expands, which heaves shallow 1960s footings and drops gates out of level. We cut out the failed post, pour a new footing to modern depth with rebar, and weld or bolt in a replacement post sized for your gate. Depending on the post diameter and whether we’re remounting an operator, post replacement in Burbank typically runs $400-$850.
Rail Repair and Custom Welding
Welding is where we separate ourselves from handyman services. A cracked rail, a separated weld at the frame corner, or a twisted top tube after a 60 mph gust needs a proper weld - not a paint-over patch job. We do full penetration welds, grind them clean, and match the finish so the repair isn’t a sore thumb. Custom welding in Burbank - building a new gate frame, extending a panel, fabricating a custom bracket - generally runs $250-$900 depending on materials and complexity. We’ll quote it before we strike an arc.
Gate Rollers, Latches, and Locks
Slide gates depend on rollers running true. When a roller seizes, flattens, or jumps the track, the gate binds and the motor strains. We replace rollers, service the track, and realign the gate so it doesn’t fight the operator. For swing gates, a worn latch or lock that won’t engage is a security issue - we address it the same visit. Roller replacement in Burbank typically runs $150-$300 per assembly; latch and lock replacement runs $120-$250.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Burbank
Your operator shouldn’t be a mystery to the person repairing your gate. We’re trained and equipped on nine major automation brands, and we service BFT, Linear, and Ghost Controls regularly throughout Burbank. That matters when a studio slide gate goes down and someone needs it running before the next production day. Our techs show up knowing the motor, the control board, and the diagnostic sequence - not flipping through a manual in your driveway. For Burbank customers, we keep a local stock of common parts on our trucks, which means less waiting on a parts order and more jobs finished the same day we start them.
Common Gate Parts & Welding Problems We See in Burbank Homes
Every city has its own gate failure patterns. Here’s what we see most often in Burbank, and why it happens here specifically:
- Santa Ana wind-load damage on solid infill gates. A 12-foot solid swing gate acts like a sail in a 60 mph gust. Frames twist past the hinge post, hinges shear, and posts pull out of plumb. We see this after every major wind event, particularly in 91501 and 91502 bungalows that still have their original gates.
- Saturated clay heaving post footings in winter. Burbank sits on clay-heavy valley soil. Winter storms saturate it, the ground expands, and shallow 1960s footings rotate. Your gate drops, catches on the driveway, or trips the loop detector intermittently. It’s not the operator - it’s the post.
- High-cycle slide gate wear along Olive and Alameda. Studio and production-facility gates in this corridor cycle 300-500 times daily. That’s a year’s worth of residential use in about a week. Rack and pinion teeth strip, rollers flatten, and factory welds crack from constant thermal and mechanical stress.
- Old frame welds separating in summer heat. Burbank’s inland summers routinely top 100°F. Metal frames expand and contract daily, which eventually cracks old welds at the corners and hinge mounts. A gate that was fine in April starts rattling and binding by August.
Pricing for Gate Parts & Welding in Burbank, CA
Here’s what Burbank homeowners can expect to pay for common gate parts and welding work, based on jobs we’ve completed in the area:
| Service | Typical Burbank Range |
|---|---|
| Hinge replacement (single gate) | $180 - $340 |
| Post replacement with new footing | $400 - $850 |
| Custom welding / frame repair | $250 - $900 |
| Roller replacement (per assembly) | $150 - $300 |
| Latch & lock replacement | $120 - $250 |
| Full gate realignment & tune-up | $180 - $380 |
These are honest ranges, not bait. What moves you within a range is the condition of the existing structure - whether the post footing is reusable, whether the frame is square enough to keep, whether the operator needs remounting. You’ll get a written price before we begin, and it doesn’t change when the job’s done. We also offer a free second opinion on any written estimate, $50 off any repair over $250, and a permanent 5% discount for seniors and veterans. Call (925) 590-4289 for an exact quote on your Burbank gate - estimates are free.
Burbank Gate Failures: What a Generic Page Won’t Tell You
Burbank’s 1940s-1960s ranch homes in ZIP codes 91501 and 91502 still carry narrow-width side-yard gates sized for post-war lots. When a hinge post twists during a 60 mph Santa Ana gust, sag correction on those gates often requires custom steel shims and footings re-poured to modern depth - a retrofit dimension we don’t see in newer Glendale tract homes. This is the kind of detail that matters if you want the gate to close square and lock properly, not just look fixed from the street.
Last January, after wind gusts over 65 mph tore a 12-foot solid infill swing gate off its hinge post on a 91502 bungalow near Disney’s campus, our crew found the original square-tube frame twisted and the post leaning 3 inches out of plumb. We cut out the bent post, poured a deeper footing with rebar, welded in a new schedule-40 pipe and HD hinge brackets, and remounted the gate with a LiftMaster operator and working safety photocell. Then we ran the manual release cycle three times to confirm smooth operation even without power. That’s the difference between a patch job and a repair that holds through the next wind event.
If you own a gate in Burbank, you should know: Santa Ana gusts bend solid infill swing gate frames past the hinge post, shearing original 1950s hinges on post-war houses. Summer heat expansion loosens factory welds on high-cycle studio slide gates along Olive Avenue, causing rack and pinion tooth skip. And saturated ground from winter storms rotates shallow 1960s post footings, dropping gates and tripping the loop detector intermittently. We know these patterns because we live in the work - and the fix starts with recognizing what actually failed.
We Also Serve Cities Near Burbank
Based out of our Los Angeles office, our crews serve Burbank daily and regularly work in the surrounding cities of North Hollywood, Sun Valley, Studio City, and Van Nuys. If you’re close to Burbank but just over a city line, we’ll still be there the same day you call. Dispatch is coordinated from our LA office, and we keep trucks staged to reach Burbank fast.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Burbank
Because the gates on Alameda Avenue are working harder. Studio and production facility slide gates in that corridor cycle 300-500 times a day, every day, which accelerates wear on rack and pinion teeth, rollers, and motor gears compared to a North Hollywood residential gate that opens maybe 10 times daily. We spec heavier-duty rack components and operators rated for that duty cycle, which extends service life significantly. If your Burbank slide gate is eating teeth, call (925) 590-4289 for an assessment - we’ll tell you if a parts upgrade or full replacement makes more sense.
Often, yes. The amount of twist, the condition of the original welds, and the thickness of the steel determine whether we can straighten and brace the frame or whether you need a new one built. For a post-war gate with sentimental or architectural value, we’ll always try to save it first - cutting out the bent section, welding in reinforcement, and re-hanging it with upgraded hinges. A new custom gate built to match the original style is also an option if the frame is beyond salvage. Either way, we’ll show you the damaged areas and explain the options before any cutting starts.
Every automatic gate operator has a manual release mechanism, usually a pull-chain, a lever, or a keyed release on the motor unit, that disengages the operator so you can push or slide the gate by hand. For BFT, Linear, and Ghost Controls operators, the release is typically a pull-down lever or a keyed cylinder on the side of the motor housing. If you’re unsure where yours is, call us and we’ll walk you through it on the phone. If the gate is heavy or the wind is already pushing on it, don’t force it - a gate that catches a gust while you’re manually holding it can injure you. Call (925) 590-4289 and we’ll dispatch someone to secure it properly.
It’s the soil, not the gate. Burbank’s clay-heavy ground expands when winter storms saturate it, which can heave or rotate shallow post footings. That shifts the hinge geometry just enough to make the gate drop and drag. In summer, the soil dries and contracts, and the gate appears to lift back into place. The fix is re-pouring the post footing to modern depth with proper rebar and drainage, which is a permanent correction - not a seasonal adjustment. We see this most often in the original 1960s installations in 91501 and 91502.
Yes. A safety photocell (or edge sensor) detects a car, person, or pet in the gate’s path and stops or reverses the gate before contact. It’s required on automatic gates, and for good reason - a solid gate moving under motor power can seriously injure someone, and Burbank’s older ranch homes often have narrow driveways where a child or pet can stand in the swing path. We install and align photocells on every gate we automate or remount, and we test the reversal function before we leave. If your gate closes without a working safety, call us - we’ll get it corrected the same visit.
Call Ironworks Gate Co. for Gate Parts & Welding in Burbank
If your Burbank gate is broken, sagging, or making a sound it shouldn’t, call the company that’s been doing this work for over 42 years. We’ll quote you a square price before any work starts, we’ll be there when we say we will, and every job is covered by our written 90-Day Done Right Promise. No fine print, no arguing. If it’s not right, we come back and make it right. That’s how we’ve built our name in Burbank, and that’s how we plan to keep it for another forty years. Call (925) 590-4289 today for a free estimate on gate parts, welding, or a full gate inspection.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Burbank, CA.