Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Access Control in Sherman Oaks: What to Know First
Linear gate access control in Sherman Oaks typically runs $240 to $680 for keypad, receiver, or intercom repairs, with full access-control panel replacements landing between $950 and $1,800 depending on the model and wiring. We are an independent Linear service provider - not affiliated with or authorized by Linear - and most access control jobs are completed in a single visit. This page is for homeowners in Sherman Oaks who own a Linear system, are tired of punching the keypad three times before the gate moves, and want an honest read on what is wrong and what it costs. Call (925) 590-4289 and a live person answers, day or night.
How Linear Products Fail - and How We Fix Them
- Linear MegaCode receivers stop learning remotes. The MGT edge receiver and the older Multi-Code 1090-series are common on Sherman Oaks driveways, and after a decade or so the learn button stops cycling through codes. Nine times out of ten it is not the receiver itself - it is a failing capacitor on the board that no longer holds the memory voltage. We replace the capacitor for a fraction of what a new receiver costs, and the remotes work again.
- Linear APeX keypads with dead columns. The ACP00742 and ACP00879 keypads used widely across the Valley develop unresponsive key columns when the ribbon connector between the faceplate and board corrodes. Sherman Oaks sees morning marine-layer moisture, and keypads mounted on west-facing pillars get the worst of it. We open the housing, clean and reseal, and replace the ribbon - no full keypad replacement needed in most cases.
- Linear telefon entry units that dial but no one hears anyone. The AE-500 and AE-1000 telephone entry systems, common on Sherman Oaks cul-de-sac estate gates, often fail on the audio side while the relay still fires. The cause is usually a blown audio transformer or a failed microphone element, both of which Linear no longer stocks. We keep quality aftermarket replacements on the truck and restore full duplex audio the same day.
- Linear ProAccess control panels losing programming. When a ProAccess controller forgets its card database every time power blinks, the problem is not the software - it is dead button cell memory on the board that was never designed to outlast a 15-year installation. We solder in a fresh cell, reload the database, and tell you honestly whether the panel needs replacing or has another ten years in it.
- Linear photo eyes that trip for no reason. The MGT obstacle transmitter and receiver pair can get so sun-faded after a few Sherman Oaks summers that the beam scatters before it reaches the reflector, and the gate reverses mid-cycle. We test alignment, clean or replace the lenses, and if the emitter is genuinely weak, we replace it with a matched aftermarket pair rather than a mismatched mix that half-works.
Our Linear Gate Access Control Process
When you call about a Linear access control problem in Sherman Oaks, here is what happens:
- 1
We listen first, then diagnose on site. You describe the symptom - keypad not taking codes, remote working only from ten feet away, intercom buzzing - and our tech arrives with Linear-specific test gear, including a MegaCode signal analyzer.
- 2
We test the whole chain, not just the part you think is broken. Many access issues are not the keypad at all. Bad wiring at the operator, a weak transformer, or a failing control board can make the keypad look guilty. We isolate the real fault before touching anything.
- 3
We show you what we found and price it before work starts. No surprises on the bill, ever. You know the number, you approve it, then we turn a single bolt.
- 4
We install OEM or quality aftermarket parts based on age and budget. On a five-year-old system, OEM Linear parts make sense. On an eighteen-year-old system, we will tell you when a quality aftermarket part does the same job for half the cost.
- 5
We test it the way you use it. Every remote, every code, every phone entry button - cycled multiple times, not once.
- 6
We write it up and stand behind it. Every job leaves with our 90-Day Done Right Promise in writing. If it is not right, we come back and fix it again. No paperwork, no arguing.
What Linear Gate Access Control Costs in Sherman Oaks
Plain numbers, because that is how we do business:
- Keypad troubleshooting and minor repair: $180 - $320
- Receiver repair or replacement (MegaCode, Multi-Code): $220 - $450
- Telephone entry audio repair (AE-series): $260 - $520
- Full access control panel replacement (ProAccess or newer): $950 - $1,800
- Complete keypad, receiver, and photo-eye refresh on a classic Linear system: $700 - $1,400
The range depends on whether we are repairing a board or replacing it, whether your wiring is still sound, and whether the system is fifteen years old or five. You get the exact price before any work begins - quoted and agreed, never adjusted after the fact. Estimates are free. Call (925) 590-4289 for a number on your specific system.
Why Sherman Oaks Homeowners Call Ironworks Gate Co. for Linear Work
We have been doing gate work - gates specifically, nothing else - for over 42 years, founded in 1984. Our owner, Victor Salinas, grew up near Van Nuys-Sherman Oaks Park and still lives in the same general neighborhood he was raised in. We are not a one-truck operation that was doing roofing last Tuesday and gates this morning. Our technicians are background-checked, uniformed, and trained on nine gate-automation brands: Linear, LiftMaster, Mighty Mule, Ghost Controls, DoorKing, FAAC, BFT, Viking, and Elite. If your Linear system is beyond saving and the right move is a full brand change, we can do that too - and we will tell you straight whether it is worth it. Every job carries the 90-Day Done Right Promise, in writing. Active offers: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a standing 5% senior and veteran discount. We will be there when we say, and we stand behind the work.
FAQs
That is almost always a receiver issue, not a remote issue - most commonly a weakened antenna connection or a failing front-end stage on a MegaCode or Multi-Code receiver. We test the receiver output with a signal analyzer, which tells us whether the problem is at the receiver or the operator. Call (925) 590-4289 and we will diagnose it on site.
Yes, in most cases. We stock audio transformers, microphones, and relay boards for AE-series telephone entry units, so a phone-entry repair that comes down to audio components is typically a single-visit job. If your panel needs a full board replacement we may need to order it, but we will tell you that before you pay anything. Call (925) 590-4289 with your model number and we will give you a straight answer.
As an independent Linear service provider, we do not perform manufacturer-warranty repair work. However, we use OEM Linear parts when the job calls for them, and we stand behind every part and repair with our own 90-Day Done Right Promise in writing. If a part fails inside that window, we replace it. No arguing, no paperwork.
If the operator itself is still running strong and only the access control components are failing, repairing the keypad or receiver usually makes the most sense - $400 in parts can buy another five to eight years. But if you are patching the same system twice a year, replacing the access control package with a newer Linear or compatible system is often the better math. We will show you both options and the price of each before you decide. We fix it right the first time, or we come back and fix it again - simple as that.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Sherman Oaks and nearby areas.