Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Installation in Sherman Oaks: What to Know First
Linear gate installation in Sherman Oaks typically runs between $2,800 and $7,500 for a complete automated driveway gate, with most single gates landing in the $3,200 to $4,800 range and double swing gates starting around $5,500. We are an independent Linear service provider, not a factory-authorized dealer, which means we answer to you and your gate, not to a manufacturer’s sales target. Most Linear installs we take on in Sherman Oaks are measured, quoted, and scheduled within five to seven business days of your call.
This page is written for homeowners who already have a Linear opener, or who are considering one, and want a straight answer about installation in this neighborhood. If you have questions that are not answered here, call us at (925) 590-4289 and a live person picks up, day or night.
Key takeaways:
- Free measure and written estimate, no obligation
- Upfront pricing agreed before any work starts
- 90-Day Done Right Promise on every installation, in writing
- We service all major Linear gate lines, plus LiftMaster, Mighty Mule, Ghost Controls, and DoorKing
How Linear Products Fail - and How We Fix Them
Linear openers are common on Sherman Oaks driveways, especially on homes built from the 1980s through the early 2000s. They are solid machines, but they have habits. Here is what we see most often when we are called out to install or replace a Linear gate in this area.
- Linear LSO series (LSO50, LSO75) - limit switch drift. The LSO line uses mechanical limit switches that slowly work loose over thousands of open-close cycles. The symptom is a gate that stops a few inches short of fully closed, or slams harder than it should. During installation, we set the limits, torque the switch mounts, and test the gate through a full open-close cycle fifteen times to catch drift before we leave.
- Linear APeX and MegaCode receivers - phantom activation. Sherman Oaks sits in a dense RF environment. Neighboring remotes, gate boards from other houses, even some garage door openers share frequencies with Linear’s 318 MHz MegaCode protocol. We have had callouts where a homeowner’s gate opened at 3 a.m. because a neighbor’s remote on a nearby street triggered it. The fix during installation is proper antenna routing and, where needed, a frequency-shifted receiver board. This is a Sherman Oaks reality, not a Linear defect, and it is one of the first things we check.
- Linear SL and SW slide line - chain stretch and rail wear. Linear’s slide operators pull hard, especially the SL series on heavier gates. After ten years or so, the drive chain stretches and the nylon rail guides wear out, causing a rumbling, jerking motion. On a new install, we size the operator to the actual gate weight, not the label on the box, and we set chain tension to spec before the first cycle.
- Linear discontinued board models - parts availability. Several Linear control boards from the mid-2000s are no longer manufactured. If a board fails on an older Linear opener, we can often source new-old-stock OEM boards from our suppliers, or retrofit a current Linear board with an adapter harness. We will tell you honestly when a board repair is throwing money after a tired motor, and when an operator replacement makes more sense than another board.
- Linear vs. aftermarket remotes - programming quirks. Linear’s MegaCode remotes are generally reliable, but aftermarket knock-off remotes, often sold online as “compatible with Linear,” frequently lose programming or fail to learn to the receiver. On a new gate installation, we supply genuine Linear remotes or proven OEM-equivalent parts, and we program and test every remote before we hand them to you.
Our Linear Gate Installation Process
Here is how a Linear gate installation with Ironworks Gate Co. actually goes, from the first call to the final walkthrough.
- 1
Call and measure. You call (925) 590-4289. We schedule a site visit, take measurements of the gate opening, check post condition, and look at the existing operator if there is one. We also check the power source and the run from the house to the gate.
- 2
Written estimate. We give you a written price before any work begins. The number we quote is the number on the invoice, full stop. No surprise charges at the end.
- 3
Parts decision. We walk through OEM Linear parts versus quality aftermarket equivalents. For safety-critical components like circuit boards and clutch assemblies, we recommend OEM. For brackets, screws, and non-load-bearing hardware, we use proven equivalents to keep cost down without cutting corners.
- 4
Installation. We hang the gate, set the posts, mount the operator, run the power, wire the safety devices (photo eyes, edge sensors, and vehicle loop if specified), then set the travel limits and force settings to Linear spec.
- 5
Testing. We run the gate through fifteen full cycles, test obstruction reversal, test every remote and keypad, and demonstrate the emergency release.
- 6
Guarantee. We walk you through the operation, hand you the written 90-Day Done Right Promise, and tell you exactly who to call if anything is not right. That person answers the phone.
What Linear Gate Installation Costs in Sherman Oaks
Linear gate installation in Sherman Oaks follows consistent pricing, but the spread is wide because every driveway is different. Here is what we typically see.
- Single swing gate with Linear LSO50 or comparable operator: $2,800 to $4,200 installed
- Double swing gate with two operators and synchronized control: $5,500 to $8,000 installed
- Sliding gate with Linear SL series operator: $4,200 to $7,500 installed depending on gate weight and rail length
- Pedestrian gate with Linear keypad and electric strike: $1,800 to $3,200 installed
- Operator-only replacement (existing gate stays): $1,300 to $2,800 installed
What moves the price is post condition, gate weight, distance from the electrical panel to the gate, and whether safety loops need to be cut into the driveway. We quote it all upfront, before a single bolt is turned. Call (925) 590-4289 for a free measure and written estimate.
Why Sherman Oaks Homeowners Call Ironworks Gate Co. for Linear Work
We have been doing gate work in the San Fernando Valley for over 42 years. Victor Salinas, our owner, grew up in Sherman Oaks not far from Van Nuys-Sherman Oaks Park, learned welding and mechanical fundamentals at Los Angeles Valley College in Valley Glen, and still lives in the neighborhood he was raised in. His father was a welder. That is how the company started, and that is still the way we build.
Our technicians are trained on Linear equipment and on eight other major gate automation brands - LiftMaster, FAAC, BFT, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule - so we are never guessing when we open a control box. Every job is backed by our written 90-Day Done Right Promise. We fix it right the first time, or we come back and fix it again, simple as that. A live person answers the phone 24 hours a day, 7 days a week. No voicemail trees, no callbacks, no waiting until Monday.
FAQs
Yes. We install Linear openers on existing gates every week in Sherman Oaks, whether the gate was built by us, by another company, or by the original homebuilder in 1987. We assess the gate’s weight, hinge condition, and post stability before quoting anything, and if the gate needs welding or hinge replacement first, we tell you before the operator goes on.
Call (925) 590-4289 and we will schedule a free site visit.
It depends on the receiver frequency and the age of your remotes. Linear’s MegaCode protocol at 318 MHz is common, but some older Linear remotes use a different coding system and will not pair with a current Linear receiver. We can tell you during the estimate whether your existing remotes will carry over or whether new remotes are needed. If new remotes are needed, the cost is included in the written quote.
A typical single swing gate installation takes one full day on site, including concrete work for the operator pad and full testing. Double swing gates and sliding gates often take two days. Power trenching, city permit requirements, and driveway loop cutting can add time. We will give you a written schedule with the estimate, and we show up when we say we will.
If your Linear opener is more than twelve years old and the control board has failed, replacement is usually the smarter money. A new operator comes with a manufacturer warranty, current safety features, and a board that is still in production. If the opener is under ten years old and the failure is mechanical, like a limit switch or a chain tension issue, repair makes sense. We will quote both options honestly and let you decide, no pressure either way.
No. We are an independent Linear service provider. That means we are not bound by factory sales quotas and we are free to tell you when an aftermarket part is just as good as OEM, or when OEM is the only way to go. We stand behind our work with our own written 90-Day Done Right Promise, regardless of what the manufacturer’s warranty covers.
If your Linear gate needs installation, a new operator, or a straight answer about whether to repair or replace, call Ironworks Gate Co. at (925) 590-4289. Free estimates, upfront pricing, and a written guarantee on every job. We have been doing this work in Sherman Oaks and the surrounding San Fernando Valley for over 42 years, and we plan to be here for another forty.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Sherman Oaks and nearby areas.