FAAC Gate Repair Nationwide

FAAC Gate Repair in Sherman Oaks: What to Know First

FAAC gate repair in Sherman Oaks typically runs between $185 and $480 for most operator and hinge jobs, and we complete the large majority of them in a single visit. The honest posture is this: we quote the price before we touch a bolt, and the number you approve is the number you pay. This page is for Sherman Oaks homeowners whose FAAC gate has stopped behaving like a gate and started behaving like a problem. If your FAAC opener is dead, sluggish, grinding, or your gate has dropped on its hinges, call (925) 590-4289 and a live person will answer, day or night.

Call (925) 590-4289

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid machine. We see them all over Sherman Oaks, especially the 400, 750, and swing-leaf models. But after enough years in Southern California sun and dust, every brand has its patterns. Here is what we find on FAAC units in this part of the Valley:

• Swing-leaf operator oil weeping at the piston seal (400 and 750 series). The hydraulic rams on FAAC swing operators hold up well, but the seals harden over time. You will see oil residue on the arm or the ground below. We rebuild or replace the ram, refill with the correct fluid, and set the leaf speed properly. A generalist will often just top off the fluid; the leak comes back in weeks.
• Capacitor failure on the 391 and 402 control boards. FAAC 391 boards run hot, and the capacitors eventually swell or pop. The symptom Sherman Oaks owners describe: the gate buzzed but would not move, or it moved halfway and died. We test the board in place, and when it is gone we replace it rather than soldering a bandage that fails in the summer heat.
• Limit-switch drift causing the gate to slam or reverse mid-cycle. FAAC operators rely on internal limit settings rather than external mechanical stops on many models. After years of use, the cams wear and the gate’s travel position creeps. We reset and re-calibrate the limits, then test under load with the gate leaf at full weight.
• Hinge and post fatigue misattributed to the opener. On heavier FAAC driveway gates in Sherman Oaks, the real fault is often the hinge weld or the post pulling out of true. The operator then struggles against a gate that no longer swings square. We repair the steel and rehang the leaf before touching the operator settings; fixing the motor while the hinge sags is wasted money.
• Photocell and safety-edge faults from Valley dust and irrigation spray. Sherman Oaks sprinkler systems and fine dry dust work into FAAC photocell lenses and edge sensors. The gate reverses for no reason, or refuses to close. We clean and reseat the sensors, and when the edge is torn or cracked, we replace it with a compatible weather-sealed unit.

Our FAAC Gate Repair Process

When you call us about a FAAC gate in Sherman Oaks, here is what actually happens:

1. 1
   You talk to a person. No voicemail tree, no answering service. We ask what the gate is doing, what model you have if you know it, and when you are available.
2. 2
   The tech arrives and diagnoses before anything is quoted. We open the operator, check the board, the motor or ram, the limit settings, the hinge load, and the safety devices. Fault-finding comes first; selling comes second.
3. 3
   You get a written price. We explain what failed, what it takes to fix it, and what it costs, including OEM and quality aftermarket options where the decision matters. The price is agreed before a single bolt is turned.
4. 4
   We do the repair. Most FAAC jobs are completed that same visit. If a part is not on the truck, we tell you when it arrives and when we will be back. We show up when we say.
5. 5
   We test under real conditions. The gate runs a full open-close cycle ten times, under load, with the safety edges and photocells triggered. No gate leaves our hands half-tested.
6. 6
   You get the 90-Day Done Right Promise in writing. If it is not right, we come back and make it right. No paperwork, no arguing.

What FAAC Gate Repair Costs in Sherman Oaks

Here is what Sherman Oaks homeowners should expect to pay for common FAAC repairs:

• Capacitor or controller board replacement (391/402 units): $220-$385
• Hydraulic ram rebuild or replacement (400/750 swing operators): $295-$480
• Limit-switch recalibration and travel reset: $125-$185
• Photocell or safety-edge replacement: $145-$260
• Hinge weld repair or post re-seating with gate rehang: $210-$390

What moves the price is access, the weight of the leaf, and whether we are splicing steel or swapping a board. We quote the job, not a menu. Estimates are free, and you will know the total before we begin. Call (925) 590-4289 for an exact quote on your FAAC gate.

Why Sherman Oaks Homeowners Call Ironworks Gate Co. for FAAC Work

We have been fixing gates in this part of the San Fernando Valley for over 42 years. Victor Salinas, our owner, grew up near Van Nuys-Sherman Oaks Park and learned welding at Los Angeles Valley College before spending decades on gates, fences, and operators across Sherman Oaks and the surrounding communities. That history matters when a FAAC ram has a hairline leak that everyone else has missed. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so when a Sherman Oaks home has two gates from two different manufacturers, one call covers both. Every job is backed by a written 90-Day Done Right Promise, and a live person answers our phone 24 hours a day, 7 days a week. We fix it right the first time, or we come back and fix it again - simple as that.

FAQs